View AN1842_8142965.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1/17 AN1842 application note january 2004 introduction the lcd monitors and tvs are growing very fast, so to support this kind of applications, a dedicated ref- erence design has been developed, taking into account all the requirements that are needed. the proposed reference design can supply an lcd monitor or an lcd-tv as well, up to 22" panels, to- gether with multimedia functions like audio. the smps accepts a full range input voltage and delivers 2 output voltages, a 5v dedicated to the scaler and p, and a 12v dedicated to the backlight and audio. the required standby power consumption is 0.8w at 230vac, in order to satisfy the worldwide power saving rules. the circuit is also fully protected against faults like output short circuit or over voltage. the market cost pressure has requested a design approach with particular attention to the solution cost. the board technology used is the standard thru-hole, but it can be changed very easily in smt because most of com- ponents are available also in this technology. the circuit has been tested deeply in all the most salient aspects with positive results and it has been integrated with a 22" lcd-tv application without showing any problem. main characteristics input voltage: 90 265 vrms - 45-66 hz output voltages: 5.1v 2% - @2a dedicated to panel and digital circuitry for scaling 12v 10% - @4a dedicated to backlight lamp inverters, audio and scart standby input power less than 0.8w @230vac, delivering 30ma on 5.1v fault protections: short circuit on each output with auto-restart at short removal, open loop safety&emc: safety: acc. to en60950, creepage and clearance minimum distance 6.4mm emc: according to en50022 class-b pcb type & size: cu single side 70 m, cem-1, 180 x 89 mm by claudio spini 60w wide-range power supply for lcd monitor or tv, using the l5991 this document describes a reference design for a 60w switch mode power supply dedicated to lcd tv sets or monitors. the board accepts full range input voltage (90 to 265vrms) and delivers 5v and 12v. it has good efficiency and very good standby performance, able to meet the most stringent standby rules.
AN1842 application note 2/17 figure 1. electrical diagram
3/17 AN1842 application note the converter topology of this smps is the standard fly back, working in discontinuous and continuous current mode. the operating frequency of the circuit (~50 khz) has been chosen in order to obtain a com- promise between the transformer size and the input filter complexity. hence, the input emi filter is a simple pi-filter, 1-cell only, for differential and common mode noise, using a 4-sectors coil filter. a ntc limits the inrush current at plug-in. the transformer is a slot type, manufactured by pulse-eldor designed ac- cording to the en60950. ferrite size is etd34, the reflected voltage is ~95v providing enough room for the leakage inductance voltage spike with still margin for reliability. the reflected voltage, the switching frequency and the primary inductance have been chosen to allow the continuous current operation of the transformer at full load, all over the input voltage range. this helps to decrease the output capacitor size thanks to the better ratio between the rms and peak current. the net- work d10, c14, r5 clamps the peak of the leakage inductance voltage spike ensuring reliable operation of the powermos, while c21, d11 and r19 limit the dv/dt of the drain voltage. the powermos is a low cost stp5nk80zfp, offering a good trade-off between the v (br)dss , the r ds (on) and the equivalent c oss , housed in standard to-220 or to-220fp packages. in this design, the to- 220fp (to-220 insulated) has been used, mounted on a heat sink and fixed by a spring. core of this de- sign is the current mode primary controller, the l5991 integrating all the required blocks to manage the control and protection of an smps. it is available in either dip-16 (l5991) or in so-16 (l5991d) packages. the switching frequency is programmable by means of a an rc network (r11, r12, c15): during normal operation r11 and r12 are connected in parallel by an internal switch (pin 16); when a light load is de- tected by the controller this internal switch is opened and the resulting frequency becomes lower, pro- grammed only from c15 and r11. if the load is further decreased the network d4, d5, r23 provides an additional frequency reduction, pro- portional to the load, allowing very low power consumption from the mains. pins 15 and 3 are set in order to allow the full duty-cycle operation and so the use of most of the energy stored in the bulk capacitor dur- ing hold-up operations. because of the current mode control and the possibility for the duty cycle to exceed 50%, a slope compensation circuitry has been added. a latched, over voltage protection has been implemented by using the pin 14 and a simple resistor net- work: in case of loop failure the circuit senses the vcc and, when the voltage at that pin exceeds the in- ternal threshold, the controller stops the operation until its vcc drops below the uvlo voltage. the start- up is done using a non-dissipative charge pump circuit to save power during standby. the output rectifiers have been chosen in accordance with the maximum reverse voltage and their power dissipation. the 5v rectifier is schottky barrier type stps5l40, a 5a-40v axial rectifier that thanks to the low-forward voltage drop is housed in a do-201 package. the 12v rectifier is an stps8h100, an high voltage schottky rectifier offering a good trade-off between the forward voltage drop and the maximum operating junction temperature. it is available from stm in 5 different package versions. for this design, the isowatt220ac (similar to a standard insulated to-220) has been used, mounted on a heat sink and fixed by a spring. on both outputs, an lc filter has been added in order to filter out the high frequency ripple without increas- ing the output capacitors size or quality. the output voltage regulation is performed by the secondary feed- back monitoring the 5.1v output. the feedback network is the typical one that uses a tl431 driving an optocoupler, in this case an sfh617a-2, to ensure the required insulation between primary and second- ary. the opto-transistor drives directly the comp pin of the l5991. here following some waveforms during the normal operation at full load:
AN1842 application note 4/17 figure 2. drain voltage & current @115 v ac - 60hz - full load figure 3. drain voltage & current @230 v ac - 50hz - full load the pictures here above show the drain voltage and current at the nominal input mains voltage during normal operation at full load. as visible, the circuit works in ccm both at nominal high and low mains. the figure 4 shows the measurement of the drain peak voltage at full load and maximum input mains voltage. the measured voltage of 672v, ensures a reliable operation of the mosfet with a good margin against the maximum bv dss . even the maximum rectifiers piv have been measured dur- ing the worst operating condition and they are in- dicated on the right of figure 5. the margin, with respect to the maximum voltage withstood by each diode, ensures safe operating conditions for these devices. figure 4. drain voltage & current @265 v ac - 50hz - full load figure 5. maximum rectifiers piv @vin = 265 v ac - 50 hz and full load here following the most salient controller ic sig- nals are shown. in both pictures it is possible to distinguish clean waveforms free of hard spikes or noise that could affect the controller correct oper- ation. ch1: v q4 - drain ch2: v pin8 (vcc) ch4: v r16 (drain current) ch1: v q4 - drain ch2: v pin8 (vcc) ch4: v r16 (drain current) ch1: v q4 - drain ch2: v pin8 (vcc) ch4: v r16 (drain current) ch3: +5v rectifier: anode voltage ch4: +12v rectifier: anode voltage
5/17 AN1842 application note figure 6. drain voltage & current @115 v ac - 60hz - full load figure 7. drain voltage & current @230 v ac - 50hz - full load ch2: v pin10 (out) ch3: v pin6 (comp) ch4: v pin2 (rct) ch2: v pin10 (out) ch3: v pin6 (comp) ch4: v pin2 (rct) cross regulation in the following tables it has been reported the output voltage cross regulation measurements with static loads. the overall efficiency of the converter is also calculated at the nominal input voltages. to check the application circuit it has been tested keeping constant the current on the 5v and varying the 12v load. as visible in both tables, the voltages are within their tolerance at any load condition and the circuit efficiency is good . 5v 2% 12v 10% tolerance 115 vac vou t [v] @iout [a] vou t [v] @iout [a] pout tot [w] pin [w] efficiency vaux [v] fs [khz] 5.106 2 12.11 4 ok 58.65 71.7 81.8% 18.3 51 5.107 2 12.23 3 ok 46.90 56.6 82.9% 17.4 51 5.108 2 12.40 2 ok 35.02 42.1 83.2% 16.7 51 5.110 2 12.72 1 ok 22.94 27.7 82.8% 16.5 51 5.110 2 13.11 0.5 ok 16.78 20.7 81.0% 16.6 51 5.108 1 11.85 4 ok 52.51 63.9 82.2% 17.5 51 5.108 1 12.00 3 ok 41.11 49.4 83.2% 16.7 51 5.110 1 12.15 2 ok 29.41 35.0 84.0% 16.2 51 5.112 1 12.39 1 ok 17.50 21.0 83.3% 15.9 51 5.112 1 12.66 0.5 ok 11.44 14.0 81.7% 15.9 51
AN1842 application note 6/17 standby operation like in the previous section, the output voltages and the efficiency have been checked, and the input pow- er has been measured. it is clearly visible that with the required standby load (5v@30ma, 12v@0ma) the input power consumption is well below 800mw at both the input voltage ranges. besides, the cir- cuit has been characterised at both the nominal input voltage values for different output load and the effi- ciency is high in all conditions. in the fig. 8, it is shown the output voltage variation as a function of the 5v current. during the standby operation the circuit works at reduced frequency, according to load and input voltage therefore, thanks to this function, the switching losses are minimized. this allows reaching very low stand- by consumption because in a power switch the switching and the capacitive losses are directly proportion- al to the working frequency. 5v 2% 12v 10% tolerance 230 vac vo ut [v] @iout [a] vo ut [v] @iout [a] pout tot [w] pin [w] efficiency vaux [v] fs [khz] 5.106 2 12.09 4 ok 58.57 69.3 84.5% 17.7 51 5.107 2 12.23 3 ok 46.90 55.3 84.8% 17.3 51 5.109 2 12.40 2 ok 35.02 41.2 85.0% 16.9 51 5.110 2 12.74 1 ok 22.96 27.6 83.2% 16.6 51 5.110 2 13.12 0.5 ok 16.78 20.8 80.7% 16.6 51 5.108 1 11.85 4 ok 52.51 63.9 82.2% 17.5 51 5.108 1 12.00 3 ok 41.11 49.4 83.2% 16.7 51 5.110 1 12.15 2 ok 29.41 35.0 84.0% 16.2 51 5.112 1 12.39 1 ok 17.50 21.0 83.3% 15.9 51 5.112 1 12.66 0.5 ok 11.44 14.0 81.7% 15.9 51 5v 115 vac vout [v] @iout [ma] pout tot [w] pin [w] efficiency 5.11 20 0.102 0.433 23.6% 5.11 30 0.153 0.515 29.8% 5.11 40 0.204 0.593 34.5% 5.11 50 0.256 0.667 38.3% 5.11 60 0.307 0.745 41.1% 5.11 80 0.409 0.881 46.4% 5.11 100 0.511 1.021 50.1% 5v 230vac 5.11 20 0.102 0.493 20.7% 5.11 30 0.153 0.582 26.3% 5.11 40 0.204 0.672 30.4% 5.11 50 0.256 0.755 33.8% 5.11 60 0.307 0.842 36.4% 5.11 80 0.409 1.008 40.6% 5.11 100 0.511 1.168 43.8%
7/17 AN1842 application note figure 8. input power @low load here following, in figures 9 ad 10 some waveforms during standby are shown: figure 9. standby @115 v ac - 60hz 5v @50ma load figure 10. standby @230 v ac - 50hz 5v @ 50ma load output voltage ripple @full load figure 11. output voltage ripple @vin = 115 vac - 60 hz and full load in figure 11 the output voltage ripples at switching frequency are measured. as shown, the ripple and the spikes are very low thanks to the addition- al lc filters added on both output and avoiding the use of bigger or expensive output capacitors. the residual line frequency modulation is very low at any input voltage. dynamic load tests figure 12 shows the output voltage regulation for a dynamic load variation of the 5v output. as shown in the picture the voltage variation and the response time are very good showing a good loop behaviour. in fact, the 5v voltage variation is less than 20mv (0,4%), and the spikes during the load transition, due to the filter inductor on the output, are only 75mv beyond the steady state (1,5%). the measured recovery time is few tens of micro- seconds. the variations induced on the 12v out- put have been also checked without showing any abnormal variation. besides, the circuit response has been verified at minimum, nominal and maxi- mum input voltage, showing no significant change. 0.000 0.200 0.400 0.600 0.800 1.000 1.200 20 30 40 50 60 80 100 iout +5v [ma] pin @stand-by pin @115vac pin@220vac ch1: v q4 - drain ch2: v pin8 (vcc) ch4: v pin6 (comp) ch1: v q4 - drain ch2: v pin8 (vcc) ch4: v pin6 (comp) ch3: +5v output voltage ch4: +12v output voltage
AN1842 application note 8/17 figure 12. +5v dynamic load 1.5 2a, 70hz +12v: full load - @115 v ac - 60hz in figure 13 it is reported the response of the out- put voltages for a load variation of the 12v output as detailed on top of the picture. the measure- ment has been done varying the 12v load from 50% to 100% load: the voltage variation is around 340mv and the 5v output is almost unaffected. therefore, the conclusion is that there is no abnor- mal behaviour of the smps generated by a load change, allowing a good confidence for the inte- gration of the smps in the equipment. figure 13. +12v dynamic load 2 4a, 70hz +5v: full load - @115 v ac - 60hz start-up behaviour @full load and wake-up time in figure14 the wake-up time is measured at the lower nominal input mains and the controller start- up sequence is shown. the vcc capacitor is charged by the charge pump circuit and when its voltage reaches the start-up threshold the device starts to operate and the output voltages begin to rise up to the nominal value, where the control loop provides for the regulation. the wake-up time at 115vac is 1.2 s, which is a quite typical time for this kind of power supplies. besides, on the pic- ture it is clearly visible that no any overshoot, un- dershoot, dip or lost of control happens during the power supply start-up phase. figure 14. wake-up time @115 v ac - 60hz figure 15. start-up behaviours @full load - @90 v ac - 60hz in the above picture the rising slopes at full load of the output voltages at minimum input mains volt- age are captured and the rise time is measured. as shown in the pictures, the rising time is mono- tonic and it is almost constant overall the input mains range. no any overshoot or abnormal be- haviour is present overall the input main range. ch3: +5 vout ch4: +12 vout ch3: +5 vout ch4: +12 vout ch1: v q4 - drain ch2: v pin8 (v cc ) ch3: +5 vout ch4: +12 vout ch3: +5 vout ch4: +12 vout
9/17 AN1842 application note turn-off and hold-up time in figure 16 the most salient waveforms at turn-off are shown. even at turn off the transition is clean, without abnormal behaviour like restarting at- tempts or loss of control by the loop. the hold-up time, in evidence between the vertical lines, is 13.6 ms at 115vac-50hz, full load and becomes around 67ms at 230vac. figure 16. hold-up @115 v ac -50hz - full load short-circuit tests at full load the short circuit tests have been done under sev- eral conditions, all over the input mains range. to avoid any catastrophic failure of the circuit due to overstress, a deep check of component stress has been done. the main circuit parameters that have been checked are the mosfet drain voltage and the mean value of the output current. the drain volt- age is an important parameter to be monitored during short circuits because an excessive in- crease due to the transformer leakage inductance and the overcurrent flowing in the primary can cause the mosfet bv dss to be exceeded. in the proposed circuit, thanks to the low leakage induc- tance of the transformer and to the start-up com- ponent correct dimensioning, in case any output is shorted, the mosfet drain voltage is below its bv dss and the mean value of the output current is low too, thus preventing component overheating because of the excessive power dissipation. in this case the reliability against long term-shorts is not affected even at 264vrms. the auto-restart at short removal has been also checked and it is cor- rect in all conditions. figure 17. short circuit on 5v @90 v ac - 60hz - full load figure 18. short circuit on 5v @265 v ac - 50hz - full load as clearly indicated by the waveforms in figure 17 and 18, the circuit works in hiccup mode, keeping the mean value of the current at levels compatible with the component rating. as visible the circuit working time is constant because it depends only on the auxiliary capacitor value, while the dead time is inversely proportional to the input mains voltage. in the following figures 19 and 20 the waveforms relevant to the 12v output in short cir- cuit at both the nominal input mains voltage are re- ported: as visible, the circuit protects itself and the load. ch1: v c13 ch3: +12v vout ch4: +5v vout ch1: vq4 - drain ch2: vpin8 (vcc) ch4: +5v short circuit current ch1: vq4 - drain ch2: vpin8 (vcc) ch4: +5v short circuit current
AN1842 application note 10/17 figure 19. short circuit on 12v @90 v ac - 60hz - full load figure 20. short circuit on 12v @265 v ac - 50hz - full load short circuit protection @ low load after the full load tests, some checks on the short circuit protection with reduced loads have been done, as reported here following. the tests have been done even at minimum and maximum input voltage with the same results, as the previous tests. @half load the waveforms of figure 21 are relevant to a short circuit test simulating a fault during normal opera- tions of the equipment, with a consumption halved with respect to the maximum output power levels (i +12v = 2a, i +5v = 1a). ? at vin = 90vac : shorting each output the over current protection works correctly, providing for the hiccup mode. ? at vin = 265vac : the circuit behaves correctly. figure 21. short circuit on 5v @265 v ac - 50hz - half load @reduced load this condition simulates a fault during an operat- ing transition of the equipment, with the backlight off and a reduced consumption of the other output (i +12v = 0a, i +5v = 0.5a). ? at vin = 90vac: shorting each output the over current protection works correctly, providing for the hiccup working mode. ? at vin = 265vac: the behaviour of the circuit is correct like at 90vac. ? @standby this condition simulates a fault during the standby operation of the equipment, with the backlight and the scaler off, and the p working with a reduced consumption (i +12v = 0a, i +5v = 33ma). ? at vin = 90vac: shorting each output the over- current protection works correctly, providing for the hiccup working mode. ? at vin = 265vac: the behaviour of the circuit is correct like at 115vac. ch1: v q4 - drain ch2: v pin8 (vcc) ch4: +12v short circuit current ch1: v q4 - drain ch2: v pin8 (vcc) ch4: +12v short circuit current ch1: v q4 - drain ch2: v pin8 (vcc) ch4: +5v short circuit current
11/17 AN1842 application note figure 22. short circuit on 5v @265 v ac - 50hz - standby load figure 23. short circuit on 12v @265 v ac - 50hz - standby load the main circuit parameter measurements have been done also during the test at reduced load or standby. in detail, during standby short it is possi- ble to check the perfect functionality of the protec- tion. this load condition in fact, is critical because all the power available from the converter can be delivered to one output only, because the others are lightly loaded or unloaded, and this can bring to the destruction of the rectifier of the shorted out- put. besides, during standby operation, the trans- former coupling and the leakage inductance may be capable of supplying the controller charging the v dd capacitor by the spikes generated at mosfet turn-off, preventing the hiccup mode. to avoid this, the circuit around q2 and q3 has been add- ed, providing the hiccup mode anyway. as visible in the pictures, the smps is always protected even in this very critical load condition. over voltage protection the open-loop operation is a very dangerous event that could happen in case of a feedback cir- cuitry failure. in this case, the smps output voltag- es can increase up to dangerous values, depending on the load by each output and the transformer coupling between the windings. thus, if the circuit is not properly protected, the rectifiers and the output capacitors can be overstressed and be destroyed or even worse, to catch light. to avoid this, the safety rules ask that the smps have a protection against the mentioned safety risks. in the proposed circuit, in case of a control loop fail- ure, a l5991 internal comparator stops the control- ler operation when the voltage at pin 14 (dis) reaches 2.5v and remains latched until the vcc voltage decreases below the uvlo threshold. so, a very safe protection with the l5991 is realized just by means of few passive components. the circuit has been tested opening the loop, the output voltages have been measured giving the following results overall the mains input voltage range: as shown in the table, in both conditions the mea- sured voltages are not critical for the circuitry. conducted noise measurements (pre-compli- ance test) the following pictures are the peak conducted noise measurements at full load and nominal mains voltages. the limits shown on the diagrams are those specified by the en55022 class-b, which is the most widely used for information technology equipment intended for domestic use, in the bandwidth 150khz 30mhz. the filter config- uration used is the 2-wires one, without the ground connection at mains plug, suitable for domestic equipment like lcd-tvs. as visible on the dia- grams, there is a good margin between the peak measures with respect to the avg limits (lower ones), and this assures that the qp and average measures will be within their respective limits. ch1: v q4 - drain ch2: v pin8 (vcc) ch4: +5v current in short circuit ch1: v q4 - drain ch2: v pin8 (vcc) ch4: +5v current in short circuit 230vac ? 50hz @full load 230vac ? 50hz @standby 5v @ 2a 12v @ 4a 5v @ 0.03a 12v @0a v 5v : 5.7v v 12v: 13.5v v 5v : 6.24v v 12v : 15.8v
AN1842 application note 12/17 figure 24. en55022 class-b peak measure @115 v ac - 60hz - full load figure 25. en55022 class-b peak measure 230 v ac - 50hz - full load thermal measures in order to check the reliability of the design a thermal mapping by means of an ir camera has been done. in the table here below the temperature of some salient components is reported at 115vac and 230vac input voltage, at ambient temperature (24c). as visible in the above table there are not component working at a temperature level that can be consid- ered critical for their reliability. @115vac @230vac point reference description temperature temperature a d9 bridge rectifier 74 c54 c b l2 filter coil 56 c40 c cq4 powermos 70 c58 c d t1 power transf. 53 c56 c e d16 +5v rectifier 61 c60 c f d13 +12v rectifier 64 c64 c
13/17 AN1842 application note board lay-out figure 26. board silk-screen and bottom plane (not in scale) original size: 89x180mm copper thickness: 70 m material: cem-1 conclusions an smps for lcd monitors or lcd-tv sets has been completely designed, assembled and tested using the l5991. all the different aspects (component electrical stress, functions, protections, conducted emi, thermal stress) have been checked, giving positive results. the design meets also low-cost and low- complexity requirements, key factors in the consumer electronic market.
AN1842 application note 14/17 references [1] "l5991 data sheet" [2] "an1537: a simple trick enhances l5991's standby function" annex1: transformer spec transformer general description application type: consumer, home appliance transformer type: open, varnished only winding type slot coil former: vertical type, 7+7 pins max. temp. rise: 45c max. operating amb. temp. : 60c mains insulation: acc. with en60065 - en60950 electrical characteristics core type/grade: etd34 - 3c90 or equivalent primary inductance: 825 h 10% @1khz - 0.25v leakage inductance: 15 h max @ 10khz - 0.25v [1] peak primary current: 2 apk [1]: measured between pins 3-7 with all secondary shorted provided by pulse-eldor p/n: 2074.5056c figure 27. electrical diagram 3 7 prim. 11 13 aux 12 10 2- 6- +5v primary secondary pins: dc output vo ltag e : rms current: number of turns: 7-3 primary 0.84 a rms 53 2/4-6/8 5v 2.6 a rms 3 12-10 12v 5.3 a rms 7 11-13 15v (aux) 0.05 a rms 9
15/17 AN1842 application note annex2: part list designator part type/ part value description supplier c1 res not mounted c10 220n - 50v cercap avx c101 (d17) 47n-400v poliester film cap mkt r66 - arcotronics c102 220p - 50v cercap avx c11 100n - 50v cercap avx c12 220n - 50v cercap avx c13 100uf-400v aluminium elcap lp4 series - elna c14 2n2-1kv hr hv cercap dehr33a222k - murata c15 4n7 - 50v cercap avx c16 4n7 - 50v cercap avx c17 4n7 - 50v cercap avx c18 330p - 50v cercap avx c19 22uf-25v aluminium elcap rubycon c2 res not mounted c20 22uf-25v aluminium elcap rubycon c21 220pf-2kv hr hv cercap dehr33a221k - murata c22 1n0 - y1 y1 safety cap. de1e3kx102m - murata c23 1n0 - y1 y1 safety cap. de1e3kx102m - murata c24 2200uf-16v yxf aluminium elcap rubycon c25 1000uf-35v yxf aluminium elcap rubycon c26 1000uf-35v yxf aluminium elcap rubycon c27 470uf-10v yxf aluminium elcap rubycon c28 100uf-50v yxf aluminium elcap rubycon c29 22n - 50v cercap avx c3 res not mounted c30 n68 - 50v cercap avx c31 3n3 - 50v cercap avx c32 47uf-25v yxf aluminium elcap rubycon c33 10n - 50v cercap avx c4 res not mounted c5 res not mounted c6 res not mounted c7 470pf - 50v cercap avx c8 220n-x2 x2 film capacitor r46-ki 3220 00 l2m - arcotronics c9 220n-x2 x2 film capacitor r46-ki 3220 00 l2m - arcotronics d10 stth1l06 fast rec. rectifier stmicroelectronics d101 1n4148 gen. purpose diode wishay d102 (r13) 1n4148 gen. purpose diode wishay d11 stth1l06 fast rec. rectifier stmicroelectronics d12 res not mounted d13 stps8h100cf power schottky rect. stmicroelectronics d14 1n4007 rectifier diode wishay
AN1842 application note 16/17 designator part type/ part value description supplier d15 1n4007 rectifier diode wishay d16 stps5l40 power schottky rect. stmicroelectronics d2 1n4148 gen. purpose diode wishay d3 bav21 gen. purpose diode wishay d4 1n4148 gen. purpose diode wishay d5 1n4148 gen. purpose diode wishay d6 bav21 gen. purpose diode wishay d7 1n4148 gen. purpose diode wishay d8 1n4148 gen. purpose diode wishay d9 2kbp06m bridge rectifier wishay f1 fuse t2a fuse 2 amp. time delay wickmann j1 input connector, 2/3 poles, 7.5mm molex j2 output connector, 9 poles, 2.54mm molex jp1 jumper wire jumper jp2 res not mounted l1 res not mounted l2 253y1r2 25mh-1.2a - cm filter inductor tdk l3 2uh-4a 2uh-4a axial filter inductor b82111 series - epcos l4 10uh rf axial choke b78108-s1103-k - epcos l5 2.7uh drum coil 2.7uh-4a elc08d series - panasonic q1 bc547a small signal npn bjt stmicroelectronics q2 bc547a small signal npn bjt stmicroelectronics q3 bc547a small signal npn bjt stmicroelectronics q4 stp5nk80zfp power mosfet stmicroelectronics r1 res not mounted r10 4k7 - 1/4w - 5% standard film resistor beyschlag r101 (d1) 100r - 1/4w - 5% standard film resistor beyschlag r11 10k - 1/4w - 5% standard film resistor beyschlag r12 12k - 1/4w - 5% standard film resistor beyschlag r14 1k0 - 1/4w - 5% standard film resistor beyschlag r15 47r - 1/4w - 5% standard film resistor beyschlag r16 1r2 - 1/4w - 5% standard film resistor beyschlag r17 1r2 - 1/4w - 5% standard film resistor beyschlag r18 1r2 - 1/4w - 5% standard film resistor beyschlag r19 4k7 - 2w - 5% power resistor 2w beyschlag r2 ntc_10r s236 ntc thermistor epcos r20 res not mounted r21 8k2 - 1/4w - 5% standard film resistor beyschlag r22 3k9 - 1/4w - 5% standard film resistor beyschlag r23 6k2 - 1/4w - 1% metal film resistor beyschlag r24 2k0 - 1/4w - 1% metal film resistor beyschlag r25 12k - 1/4w - 1% metal film resistor beyschlag r26 1k5 - 1/4w - 5% standard film resistor beyschlag part list (continued)
information furnished is believed to be accurate and reliable. however, stmicroelectronics assumes no responsibility for the co nsequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of stmicroelectronics. specifications mentioned in this publicati on are subject to change without notice. this publication supersedes and replaces all information previously supplied. stmicroelectronics prod ucts are not authorized for use as critical components in life support devices or systems without express written approval of stmicroelectro nics. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners ? 2004 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - singapore - spain - sweden - switzerland - united kingdom - united states www.st.com 17/17 AN1842 application note designator part type/ part value description supplier r27 10r - 1/4w - 5% standard film resistor beyschlag r28 82k - 1/4w - 5% standard film resistor beyschlag r29 2k43 - 1/4w - 1% metal film resistor beyschlag r3 470k - 1/4w - 5% standard film resistor beyschlag r30 2k43 - 1/4w - 1% metal film resistor beyschlag r31 1k0 - 1/4w - 5% standard film resistor beyschlag r32 47k - 1/4w - 5% standard film resistor beyschlag r33 12k - 1/4w - 5% standard film resistor beyschlag r34 3k3 - 1/4w - 5% standard film resistor beyschlag r35 10k - 1/4w - 5% standard film resistor beyschlag r4 470k - 1/4w - 5% standard film resistor beyschlag r5 150k - 2w - 5% power resistor 2w beyschlag r6 33r - 1/4w - 5% standard film resistor beyschlag r7 res not mounted r8 res not mounted r9 res not mounted t1 2074.5056c power transformer pulse-eldor u1 l5991 primary controller with standby stmicroelectronics u2 sfh617a-2 optocoupler infineon u3 tl431acz shunt regulator stmicroelectronics heat sink for q4 rth hs-amb = 15c/w p/n 6098b thermalloy with clamp heat sink for d13 rth hs-amb = 10c/w p/n 6099b thermalloy with clamp part list (continued)

▲Up To Search▲

Price & Availability of AN1842

	To Download AN1842 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .